Dakota Durango Forum banner


41366 Views 24 Replies 14 Participants Last post by  Ebeard0502
A lot of Hemi swaps going lately, which is a really good thing.
A lot of pictures to follow along which is also a good thing.

There is 1 thing lacking the ELECTRONICS part.

I know there isn't much that can be shown with pictures and talking/writing about isn't that exciting either. I'm an electronics guy by profession and training coordinator to boot. I know how dry the stuff is.

BUT I would like to see some plain and simple feed back from some of those that have done the swaps and what they have found out.

What year Daks would be the easiest and which would be the hardest?

I did notice Mention of 2 different CAN types used (2-wire and 1-wire). What year Dak and What year Hemi vehicles use those?

What wiring harnesses to use.

Reason I throw this out there is because I have no daily driver right now and looking to buy when I return home. With a swap in mind from the beginning, what year Dak would be the easiest?

And for those that have a Dak already what exactly are they up against electronically.

I just spent the last week studying some info on the Chrysler Crossfire.

A guy in Dallas just finished putting a Mercedes V8 in his. Which a lot of so-called MB experts said couldn't be done.

Not only was it possible! He did it with all MB parts, it looks Factory, runs on factory software, no electronic conflicts, and he didn't have to modify but 2 wires that were just too short.

Only 1 issue he ran into, the car will not start with the key. He had to install a Start Button (which I am fine with, done right actually looks kool). He and his MB contacts think it is because they used an ECU from a car that uses and RF Key not a mechanical key. Unfortunately only 3 cars with the same ECU use a mechanical key, only 1 uses a V8. Last I read he was going to attempt to use an ECU from that car and see if he gets his Key Start back.

After he was done and running He also went into details of what too look for when buying an engine, wiring Harness and ECU from a Donor car so you can make everything work with minimal issues.

Granted it was by no means plug and play. Mechanically everything went together like factory (engine wiring harness ecu etc)

Where he ran into issues was the Association of the Contol Modules through out the vehicle. Which he solved with a Copy of MB C3 Star system and a guy that has the capability of resetting the VIN number in the ECU. (IE: virgining the ECU)

Luckily we don't have to go that deep in the software!!

I think I do remember someone that was going to do a 4.7 to 5.7 swap saying that they put the 5.7 PCM in their truck and it ran. If i am remembering correctly what ever year this was would probably be the easiest to swap.

From my understanding about the only difference on the engines (4.7 to 5.7) as far as connectors go is the Electronic Throttle on the TB.

All those that know the details please share.

See less See more
  • Like
Reactions: 1
1 - 1 of 25 Posts
A. What's your timeframe?

B. What's your budget/offer for this? This and the timeframe are important, because if you need it back pronto, it's going to cost you more than if it's something I can work on in spare time.

C. Are you prepared to ship me both harnesses and pay for shipping both ways?

D. I'll need high quality/high resolution pictures of the engine bay with the 5.7 installed, along with some indicator of scale (ideally just run a tape measure from the firewall across the top of the engine to the radiator core before you start taking pics). If any sensors or anything are in significantly different places, make sure they are clearly identified on the pics of the new engine. I have a 4.7 in mine so I know where they WERE, I just need to know where they're GOING.

E. Are you going to want the whole thing taken apart, cleaned and re-taped/re-loomed so it looks brand new or are you ok with how it looks now (ie: is the rest of the engine compartment going to be cleaned/painted/dressed up or is this just "make it work")?
See less See more
  • Like
Reactions: 1
1 - 1 of 25 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.