PRODUCT:  PCM MODULES
CLICK HERE FOR FORUM DISCUSSION : PCM MODULES

PCM REPROGRAMMING SERVICES

MANUFACTURER:  B&G Chrysler
WEBSITE:  http://www.bgchrysler.com
CONTACT INFORMATION:
Dave Kaspar
2076 East Ten Mile Road
Warren, Michigan 48091
(586) 758-2003

PRODUCT INFORMATION:
"Let B&G Wake up your Magnum's Engine Performance"
We offer complete custom PCM modifications. Using emulators, software, and device programmers, with the latest technology to customize your vehicle performance.

Contact Dave Kaspar for further PCM flash details.

INSTALLATION INSTRUCTIONS:
This is a PCM Flash Service - you must remove the PCM from the fender of your truck, and ship it off to this company for reprogramming.  The company will send your PCM back and you must re-install it in your truck.

MANUFACTURER:  Kenne Bell
WEBSITE:  http://www.kennebell.net
CONTACT INFORMATION:
10743 Bell Court
Rancho Cucamonga, CA 91730
(909) 941-6646 Sales
(909) 941-0985 Tech
KenneBell@KenneBell.net

PRODUCT INFORMATION:
With the introduction of the new OPTIMIZER ll, Kenne Bell has now made the commitment and dedicated the resources necessary to engineer and optimize the computer performance of both supercharged and normally aspirated Chrysler vehicles.

For 4 years we dyno, street and track tested the OPTIMIZER ll on our fleet of company vehicles until the computer calibration upgrades met our performance goals - optimum power, improved mileage, acceleration and transmission operation for each vehicle at part and full throttle - performance you can really feel!

Power gains vary depending on the vehicle, but improvements are typically in the 10% range. Every OPTIMIZER chip has been precision dyno tuned and tested on your specific vehicle. We have improved the shift quality and increased engine horsepower at the WOT shift points. Note: Stock calibrations actually reduce HP at the gear changes to "soften" the shifts. The OPTIMIZER ll puts this horsepower back in and uses it to accelerate the vehicle. This two pronged Kenne Bell approach increases engine HP (up to 25HP) and reduces trans slippage.

Contact Kenne Bell for further details.

INSTALLATION INSTRUCTIONS:
This is a PCM Flash Service - you must remove the PCM from the fender of your truck, and ship it off to this company for reprogramming.  The company will send your PCM back and you must re-install it in your truck.

MANUFACTURER:  KRC Performance
WEBSITE:  http://www.krcperformance.com
CONTACT INFORMATION:
(321) 635-8866
techsupport@krcperformance.net

PRODUCT INFORMATION:
Custom PCM Flashes performed by B&G Chrysler but using specifications provided by KRC Performance based off of your engine modifications.

Contact Marty Fletcher for further details.

INSTALLATION INSTRUCTIONS:
This is a PCM Flash Service - you must remove the PCM from the fender of your truck, and ship it off to this company for reprogramming.  The company will send your PCM back and you must re-install it in your truck.

MANUFACTURER:  Mike Leach
WEBSITE:  N/A
CONTACT INFORMATION:
Contact via Sam Parthemer at www.socaldakota.com

PRODUCT INFORMATION:
No details available at this time - will update soon.

INSTALLATION INSTRUCTIONS:
This is a PCM Flash Service - you must remove the PCM from the fender of your truck, and ship it off to this company for reprogramming.  The company will send your PCM back and you must re-install it in your truck.

PCM PROGRAMMER MODULES

MANUFACTURER:  Hypertech
WEBSITE:  http://www.hypertech.com
CONTACT INFORMATION:
3215 Appling Rd
Bartlett, TN 38133
(901) 382-8888
techsupport@hypertech.com

PRODUCT INFORMATION:
Increasing horsepower and torque is as simple as pushing a button with Hypertech's Power Programmer III! Simply plug the Power Programmer into the underdash diagnostic plug, answer a series of "Yes/No" questions, and the Power Programmer does the rest. The Power Programmer is much more than a tuning chip. It is a self-contained automotive tuning computer!

When you connect the Power Programmer to your vehicle, its "smart" program instantly recognizes your vehicle's powertrain by reading the Vehicle Identification Number (VIN). The VIN contains specific information on the engine, transmission, and drivetrain, which the Power Programmer decodes before it downloads the Power Tuning program that is precisely tailored to your car or truck.

The Power Programmer lets you choose Hypertech's Power Tuning program for regular 87 octane or premium 93 octane gasoline. Both options improve performance without detonation. After the tuning program is selected, the Programmer automatically installs the program and allows you to access and reprogram the vehicle's computer to function properly with aftermarket components such as non-stock tire sizes and rear-end gear ratios.

The Power Programmer is incredibly powerful, but it is also incredibly easy to use. Reprogramming does not require any tools or knowledge of cars or even computers. Plus, you can return to OEM (stock) programming in just minutes.

MODEL AVAILABILITY / PART NUMBERS:
2002-03 Dodge Truck and SUVs with 5.2L/5.9L - Part #50008
2001 Dodge Truck and SUVs with 5.2L/5.9L - Part #50006
2000 Dodge Truck and SUVs with 5.2L/5.9L - Part #50005
1999 Dodge Truck and SUVs with 5.2L/5.9L - Part #50004
1998 Dodge Truck and SUVs with 5.2L/5.9L - Part #50003
1997 Dodge Truck and SUVs with 5.2L/5.9L - Part #50002

INSTALLATION INSTRUCTIONS:
Connect the programmer module to your vehicle's OBD port and follow the manufacturer's instructions.

MANUFACTURER:  Superchips
WEBSITE:  http://www.superchips.com
CONTACT INFORMATION:
1790 E. Airport Blvd
Sanford. FL 32773
(407) 585-7000
tech@superchips.com

PRODUCT INFORMATION:
The TriTune Max MicroTuners allow the end user to custom tailor their desired performance level to the specific driving task at hand. 87 Octane / 91-93 Octane Performance Tow Program and 91-93 Octane Performance Program.

User adjustable options:
* Increase rev limiter
* Raise top speed limiter
* Calibrate for changes in tire height

The 3715 MAX MicroTuner also provides the ability to read and clear Diagnostic Trouble Codes (DTC).

MODEL AVAILABILITY / PART NUMBERS:
Part #3715 - All 1997-2003 Dakotas and Durangos
Module currently not available for 2004 model trucks.

INSTALLATION INSTRUCTIONS:
Connect the programmer module to your vehicle's OBD port and follow the manufacturer's instructions.

MANUFACTURER:  SCT
WEBSITE:  http://www.sctflash.com
CONTACT INFORMATION:
975 Florida Central Parkway - Suite 1900
Longwood, FL 32750
(407) 774-2447

PRODUCT INFORMATION:
The SCT XCalibrator 2 Custom Tuning PCM Flash Tool is designed to be used with our Advantage III Custom Tuning Software Package. The XCalibrator 2 will store up to 3 Custom Tune files created by your SCT DCX Custom Tuner, while storing the stock factory tune for easy restoration back to the stock configuration. Flashing your Dodge truck with a custom tune specifically calibrated for your vehicle has never been easier! SCT’s XCalibrator 2 instantly adds MORE POWER, MORE TORQUE and can even INCREASE your vehicle’s FUEL MILEAGE!

MODEL AVAILABILITY / PART NUMBERS:
XCalibrator 2 DCX Flash Device

MANUFACTURER:  Mopar Performance
WEBSITE:  http://www.mopar.com

PRODUCT INFORMATION:
This controller adds spark, fuel, moves the rev limiter to 6000 rpm, removes the speed limiter, has a higher initial spark curve, moves the shift points from 4800 to 5200 and locks out the AC compressor under WOT.  Not available for Dakota/Durango 2001+, must use a PCM flash or programmer.

PART NUMBERS:

Note (1): N/A Durango R/T